Control of technical parameters in asphalt mixing station mixed with concrete

From the above content can be seen, it is precisely because of the heating, heat from the hot end of the continuous transfer to the cold end, and which and then passed to the hot end, so that the continuous circulation, so as to meet the asphalt mixing station in the process of the relevant requirements, to achieve the requirements of cyclic heating.

No matter what type of asphalt mixing station, they are used in the process of admixture concrete, in the dosage, blending methods and mixing time must be strictly controlled, can not be ignored because of the small amount of admixture, can not be less admixture as a saving, there is no need to shorten the mixing time as an accelerated progress.

Check contactor, motor interphase resistance, grounding resistance, interphase voltage, etc., did not find the problem; Remove the transmission tape, start the vibrating screen, the ammeter indication is normal value (10A), no-load Operation 30min also has no problem tripping phenomenon, indicating that the fault is not in the electrical part.

In short, in the asphalt mixing plant working process, due to the realization of the cycle of antipyretic this condition, thus also ensure that our asphalt products to achieve the best state.
This not only ensures our production requirements, but also provides favorable conditions for our next production work.
Hope that through this analysis, so that we have a new understanding and understanding of this knowledge.

　　Remove the eccentric block, start the vibrating screen, the ammeter is displayed as 15A, fix the magnetic table seat on the Vibrating screen box board, use the needle to check the radial beat of the shaft end, and measure the maximum radial beat amount of 3.
5mm; The maximum elliptic degree of the bearing inner diameter is 0.
32mm.

For this question, in fact, it is also very good understanding.
We need to start with the structure of the asphalt mixing station equipment.
Usually, it is composed of a sealed shell, a suction core close to the surface of the shell, and a working fluid encapsulated in the shell after the shell is vacuumed.
Therefore, when a heat source is used to heat one end of its heat pipe, the working fluid in it will boil due to heat and eventually evaporate.

In the process of evaporation, because there will be a pressure difference in the asphalt mixing plant equipment, under the action of pressure difference, these steam will flow to the cold end of the heat pipe at a very high speed, and then by the which release of latent heat and condensation occurs.
We know that because of the effect of the suction core capillary suction, these condensate will return from the cold end to the hot end again.

Asphalt mixing equipment Manufacturers in the design of asphalt mixing equipment, in addition to the structure of the equipment, functions, such as the focus, asphalt mixing equipment color design is also considered in the internal, for the satisfaction of all aspects of the requirements.
So, which color does the asphalt mixing equipment use mainly depends on what?

Of course, the use of the method is also appropriate, need to be hydrolyzed after mixing can not dry mix, the need for powdery mixing of the agglomeration can not be used.
such as water reducer or aerated agent, the poor control will appear in the concrete soft solid group, in the solid concrete formation pores.

1th, to be familiar with the construction site line direction, because the transport distance of asphalt directly affects the quality of Asphalt Mixing Plants, so the construction of asphalt soil mixing station must be fully considered, so that it fully meet the needs of the field.
It is necessary to fully confirm the distribution of asphalt according to the construction drawings in order to locate the approximate central position of the asphalt mixing station.

2nd, to understand and master the basic elements of mixing plant construction, including water, electricity and floor area, and finally about the construction site surrounding the environment, because the asphalt mixing station is a high degree of mechanized construction of the processing base, so dust, noise and other pollution will be more serious, which requires that site selection should be avoided as far as possible residential groups, schools, Breeding base and other people, livestock more concentrated areas, as far as possible to reduce the impact of the most surrounding environment.

In other words, during the work of the asphalt mixing station, each tank of concrete must be quantified enough, can not sometimes be mixed sometimes not mixed.
such as Retarder, in a barn of concrete if there is a retarder concrete and no slow concrete appearance, because the solidification time is not uniform, it will cause cracks in the concrete.

I wonder if your friends have learned more about the work of the asphalt mixing plant.
If you have a certain understanding, then you should know that the asphalt mixing plant equipment has a more special function, this function is to be able to carry out circulating heating, so that the asphalt products to achieve the best state.
So how is this feature implemented? Next, let's take a look at the specific introduction.