Veneer peeling machine The reason for the knife drop

.


veneer-composer.jpg4. Increase the transmission shaft, increase the torque, so that the single and double roller transmission part is not easy to fail.
The upper sliding bar presses the single roller box, which reduces the jitter phenomenon of the blade in the process of rotary cutting.

Veneer peeling machine is a good helper for spinning wood, improving the utilization rate of wood, won the welcome of wood machinery Factory.
Now more commonly used veneer peeling machine have card veneer peeling machine, card veneer peeling machine, CNC veneer peeling machine, and so on, they each have its advantages and characteristics.
Today we mainly come to understand the main features of the next dual-boot card-free veneer peeling machine:

CNC Card-free veneer peeling machine is developed on the basis of ordinary veneer peeling machine, there is a card shaft veneer peeling machine in the process of rotary cutting the remaining wood core can not be spun, resulting in wood capital The waste of the source also increases the cost, while the CNC veneer peeling machine is designed for the remaining wood cores, which improves the utilization rate of wood.
In addition, CNC card-free veneer peeling machine not only improve the quality and accuracy of the single board, but also improve the work efficiency.
CNC Card-free veneer peeling machine The use of a long time will inevitably appear a small problem, such as veneer peeling machine knife dull, skin deformation and other reasons, these need users to regularly check maintenance veneer peeling machine To reduce the probability of veneer peeling machine failure, resulting in savings in maintenance costs.
The inspection and maintenance of the card-free veneer peeling machine mainly from the following aspects to consider:

:

To maintain a card-free veneer peeling machine performance stability and safety, should be checked according to the following frequency: The new equipment should be guided shaft, hanging wheel frame, clutch gear, roller shaft and other moving parts to add lubricating oil, guide shaft, hanging wheel frame, clutch gear, roller shaft and other places should be in the new machine within 40 hours, Lubricating oil is required 1 times every 2 hours; After 200 hours of operation of the equipment, each lubrication component is lubricated 2 times every 8 hours; After 200 hours of work check whether the control buttons are working properly; the single double roller drive motor triangle belt or chain is worn or loosened, and adjusted and replaced in a timely manner.

.


2.6 Meters There is a card veneer peeling machine appear to drop the knife can use the automatic knife change program patiently check, when the manipulator is not in place, the spindle on the tool will be loosened, resulting in the manipulator did not catch the tool to produce the knife.
Check the connector of the sensor switch, check the terminal at the point of no loosening, manipulator action will cause slight vibration, if the switch lead has loose will lead to bad contact, then the manipulator is not fully in place, and magnetic induction switch is still in the sensing state, if in the state of disconnection, the tool will release caused by the knife.

.

Secondly, according to the production requirements, adjust the mechanical parameters, confirm the correct to boot operation.
Do not adjust mechanical parameters in the operation of the equipment.
Mechanical operation, to carefully observe the operating state of the machinery, such as the discovery of abnormalities should be shut down to check.
When the wooden section is clamped to ensure the concentric position of the two ends, the wooden segment clamping must be carefully checked to see if the chuck is stuck.

:

1. Dual-boot card-free veneer peeling machine machine at both ends at the same time, reducing the power of the single double roller head and reducer shaft head, reducing the failure rate of the machine tool.
Since both ends are activated at the same time, the Rotary force of the machine tool increases, so it adapts to the hard wood processed in the south.
such as pine, miscellaneous wood, maple wood.

.


5. Flower Roller opening tile, easy to disassemble, more accurate positioning.
Change plate skin thickness, with fine-tuning mechanism, so that the plate skin is easier to adjust uniformity better.

We all know that 2.6 meters of card veneer peeling machine is a necessary mechanical equipment for the production of Plywood Making Machine, and veneer peeling machine knife is an important part of veneer peeling machine equipment, the quality of the swivel knife on The spin-cutting efficiency of wood has a crucial impact.
But we veneer peeling machine in the automatic change of knife will appear to drop the knife situation, affecting the efficiency of production, more importantly, will damage veneer peeling machine, so veneer peeling machine drop knife phenomenon can not be ignored, We should find out the reason in time, take the right medicine and find out the solution.
Modern veneer peeling machine manufacturers to tell us about veneer peeling machine why drop the knife and the corresponding solution.