Parameters of veneer peeling machine-

　　Veneer peeling machine is used to process a certain length and diameter of wood segments into a continuous single strip for the production of plywood, for the production of plywood, joinery boards and other wood-based panels using veneer peeling machine The main technical parameters have the maximum length of the machined wood segment, Diameter type.
According to the maximum length and diameter of the machined wood segment: Heavy, medium, small.
According to the clamping and driving mode of the rotary cut wood section: Mechanical clamping card shaft, hydraulic clamping card shaft (double axis, single axis) hydraulic clamping card shaft (double axis, single axis), shaft.

Rotary cutting Chopper leather All-in-one machine is a wood processing equipment, its degree of automation, on the integration of the material spinning, than the ordinary veneer peeling machine efficiency, suitable for small diameter logs and card veneer peeling machine remaining wood shaft reprocessing, processing Pi Zihou degree from 1.0~2.6mm, processing wood shaft length changes, as well as the size of the wood shaft diameter, the user can be selected according to their own needs, with its spinning wood skin can be used as a wood-based panel sandwich or skin.
So the rotary cut chopper leather All-in-one machine is very popular.
As a result of the rotary cut chopper leather All-in-one machine often spin hard wood, so a long time will inevitably become dull, work efficiency decline, then we need to maintain it on a daily basis.

　　Veneer peeling machine working principle is that the wood section is driven by the card shaft rotation, the knife bed relative rotation of the wood section to do into the movement, spin out a continuous single strip, for rotary cutting.

The Daily maintenance of rotary chopper leather All-in-one is best carried out by a person, from one end understand the machine situation, easy to maintain veneer peeling machine, extend the service life.

The Daily maintenance of rotary-cut chopper leather All-in-one includes daily cleaning and lubricating oil and so on.
Rotary Cut Chopper leather All-in-one after each use to clean up the above wood chips, in order to prevent wood chips into the plug into the seam, affecting the spin efficiency.
In order to prevent veneer peeling machine corrosion, regular lubrication should be added.
How much lubricant used in the Rotary chopper leather All-in-one machine should be confirmed according to the type of machine, as well as the viscosity of the oil.
The use of lubricating oil is easy to be affected by temperature, so according to the season situation to buy.

　　Using a height meter or equivalent to the height of the center line of the card shaft as a standard, by adjusting the support screws, so that two Rui knife higher than the specified H value in the rotary cutting process, and fasten all nuts.

　　Veneer peeling machine is one of the equipment for the production of plywood, it belongs to the shaft mechanical transmission veneer peeling machine, suitable for the card shaft veneer peeling machine rotary cutting remaining wood core continue to spin into a single board, It can also be used to spin the trail material (300mm in diameter) into a single board.
Veneer peeling machine is mainly composed of rack, double roller system, single roller system, tool holder, transmission system, electrical system and so on.

The gap between the nut and the screw of the propulsion tool holder should not be too large, otherwise the knife holder produces vibration when spinning the wood, which affects the spinning quality of the veneer.
The screw nut gap can be adjusted by adjusting the anti-loosening nut.

　　In the absence of a post-test angle meter, after changing the knife, with experience to adjust the back angle, driving rotary, to pay attention to the entire rotary cutting process into the knife is smooth.
To observe the bright width of the friction part between the blade of the rotary cutter and the surface of the wood section, it is appropriate to determine whether the posterior angle is adjusted properly.

First, use the grinder to grind the back of the rotary blade into a 19-21-degree wedge angle, and then grind the blade with the oil stone.
Because of the deflection of the spinning wood, the blade should be slightly curved to form an upward curvature when the blade is installed, the value of which depends on the properties of the spinning wood and the minimum diameter of the log remaining at the end of the rotary cut (usually about 0.15M). This can be done in this way.
When the clamping screws at both ends of the blade are fastened, adjust the middle top lever so that the blade can form an upward curvature and then tighten all clamping screws, and the mounting angle of the blade can be adjusted by turning the hand wheel.
In addition, the blade in the installation of the center level of the card shaft, the tip height is 0.1-0.20mm, the two ends of the knife must be exactly the same height.