The difference between veneer peeling machine and wood planer

　　The pressure ruler friction roller adjustment mechanism of the veneer peeling machine has manual adjustment and automatic adjustment mechanism, and the automatic adjustment mechanism automatically adjusts the seam gap between the ruler and the rotary cutter in the process of single plate rotary cutting, and decreases with the smaller diameter of the circular wood, So that the smooth and uniform of the single plate (high-quality wood can reach ±0.05mm), the finish is better than the ordinary card-free shaft veneer peeling machine rotary veneer, the remaining wood shaft will not appear square shaft, the spinning process will not appear the phenomenon of falling knives, jumping knives, The spinning veneer will not appear concave plate (also known as corrugated plate) and broken sheet defects.

In a blink of an eye spring has passed, summer quietly came, oncoming is not the biting cold wind, genial spring breeze, but a hot warm wind, summer people most afraid of being tanned, whether handsome or beautiful women are taking a variety of protective measures, sun hats, umbrellas, sunscreen as well, Usually we just pay attention to our own protection, in fact, a lot of things around us also need to be protected, such as some veneer peeling machine and other daily daily necessities also need to be sunscreen.

The breath of summer is getting stronger, the sun is getting bigger and larger, and while we are doing our own sunscreen measures, we should also make sun protection on some of the large devices around us, such as veneer peeling machine, and don't let him bask in the sun, not only let the color of the surface fade away, It will also shorten their lifespan and move them under the shade for sun protection, allowing them to generate greater economic value for us.

　　There are several combinations of the common design of the knife bed rails of the card-free veneer peeling machine:
　　The first combination is a double triangle combination.
The structural features of this combination are:
　　Two triangular rails play a supporting and guiding role at the same time, the parallel degree requirements of the two rails are high, there is no need to adjust the gap, contact stiffness is good, there is no gap between the guide surface, the guidance accuracy is high, the relative position changes after wear is small, the impact on the machine tool accuracy is small, can compensate for the vertical and horizontal

　　1, send the power supply, the indicator light is on, the motor can not start.
Cause: Power supply phase missing or main control line virtual connection.
Workaround: Overhaul the power supply and control line and the total Stop button.

　　8, the plate skin is not connected.
Cause: knife too high too low, knife seam and into the knife hanging wheel with bad, yin and yang noodles.
Solution: Adjust the knife height, knife seam and inlet knife hanging wheel, change wood.

1, when the lubricant flow to the friction site, will adhere to the friction surface to form a layer of oil film, reduce the resistance between the components, so veneer peeling machine The higher the speed of rotation or sliding, the smaller the viscosity of lubricating oil, the operating temperature is high, the viscosity of the use of oil should be increased;

Veneer peeling machine One of the main equipment for the production of wood peel, veneer peeling machine according to whether the wood section rotates around its axis can be divided into two categories, concentric rotary and eccentric rotary cutting.
The concentric veneer peeling machine is divided into two types of card axis veneer peeling machine and no-card axis veneer peeling machine.
The eccentric rotary cut can obtain beautiful radial pattern, but the productivity is lower than the concentric spin cut.
There is a card veneer peeling machine generally large size and complex structure, before the machine need log centering, if the centering is not allowed, start spinning will spin out the intermittent single strip or narrow veneer, more waste of wood costs.
And when the diameter of the log is reduced to a certain extent, it can no longer continue to spin (that is, the remaining wood core caused by wood waste).

There are cards veneer peeling machine in our lives have played a very important role in promoting the development of the timber industry, to our production and life has brought great help, in fact, in this summer, not only we need to carry out sunscreen, like some of the equipment around us also want to sunscreen them , often in the sun to be exposed not only on the surface will fade will also greatly reduce the service life of these items, not only we are afraid of ultraviolet radiation, for these devices also need to be sunscreen, usually after use to put them in a cool place, do not put in the sun to the place, Taking these sunscreen measures is a good way to protect them, increase their lifespan, and allow them to create greater economic benefits for us.