Matters needing attention for veneer peeling machine plus lubricants

(8) After the center frame is assembled, its center and spindle centerline require concentric, allowing error of 0.2 mm.
The knife guide rail in the vertical and horizontal direction requires a horizontal plane, its deviation in the length of each meter is not greater than 0.03 mm.

No card veneer peeling machine sometimes in the use of the case may appear uneven skin, this situation does not mean that there is no card veneer peeling machine quality problems, can only be some aspects of the existence of inappropriate.

The main drive motor drives the press roller constant speed operation, the passive roller and the knife bed driven by the feed motor, according to the real-time diameter of the log and set the wood skin thickness variable speed operation, the smaller the diameter, the faster the feed motor push the knife bed speed, to ensure that the spinning veneer thickness is uniform.

　　The second case is because the knife is too small or the single roller is too high, usually said to be stressed.
Knife tool with a angle ruler and a ruler.
The height of the knife and the height of the roll depends on how thick the skin you do and the diameter of the drum to set.

There is a card veneer peeling machine is one of the main equipment for the production of plywood, widely used in the wood industry, and most machinery, the long-term use will inevitably appear small problems, such as in the operation of running a lot of noise, which is more annoying situation.
Here's our analysis of the cause of noise in the operation of a card veneer peeling machine.

Veneer peeling machine During their work, they rub against each other and produce enough heat over a long period of time to melt the metal, causing damage to the machine or even the death.
Therefore, it is necessary to give the friction area in the engine, add lubricating oil, reduce the wear between parts, but also improve the efficiency of veneer peeling machine, extend its service life.
However, there are several issues to be aware of when adding lubricants to veneer peeling machine.

No card veneer peeling machine already has this error of positive and negative 0.3mm, which is a normal situation, if it is within this range of the situation, then we should be considerate of this error; in another case, there is no card veneer peeling Machine's knife height is inconsistent or the knife table is inconsistent.
This situation is necessary for us to monitor the inspection at all times, only to ensure good to get better skin.

5, veneer peeling machine work, will produce a lot of dirt.
These dirt will attach to the friction surface of the machine, if not cleaned down, will increase the wear of the machine parts.
Therefore, these dirt must be cleaned up in a timely manner, this cleaning process is done by the circulating flow of lubricating oil in the body.

1, when the lubricant flow to the friction site, will adhere to the friction surface to form a layer of oil film, reduce the resistance between the components, so veneer peeling machine The higher the speed of rotation or sliding, the smaller the viscosity of lubricating oil, the operating temperature is high, the viscosity of the use of oil should be increased;

　　Veneer peeling machine is one of the main equipment for the production of Plywood Making Machine, divided into card veneer peeling machine and unlicensed veneer peeling machine, with the advancement of Science and technology digital control technology is also applied to veneer In the production of Peeling machine machine, CNC veneer peeling machine appeared in recent years.
The appearance of CNC veneer peeling machine not only improves the quality and precision of the production single board, but also greatly improves the production efficiency and the automation degree of the whole machine.
CNC Card-free veneer peeling machine is an important equipment on the plywood production line or veneer production line, mainly used for the use of the card shaft veneer peeling machine rotary cutting the remaining wood core for two times, will be of varying lengths of wood segments, The wood cores in a certain diameter range are cut into veneer of different thicknesses, and the diameter of the rotary cut is small.
Veneer peeling machine gnawing knives generally have two conditions:
　　One: When the wood shaft is large in diameter.

Veneer peeling machine in our timber industry has played an important role in the development of the timber industry has played an important role, is an indispensable equipment for many plywood plants, there are cards veneer peeling machine can be rotated any number of segments, rotary cutting The plate is thin and uniform, in order to ensure the smooth and safe operation of the card veneer peeling machine, the following technical requirements should be followed when installing the card veneer peeling machine:

When there is a card veneer peeling machine motor rotor and wood powder machine rotor different heart, will let the bearing bear additional load impact, resulting in the overheating of the bearing, resulting in continuous heating in the bearing to make a lot of noise.