CNC Unlicensed veneer peeling machine safety operating Procedures-

.

　　Veneer peeling machine's card shaft diameter reduces the diameter of the wood core, which can effectively increase the plate rate.
The most direct and intuitive way to reduce the diameter of the wood core is to directly reduce the diameter of the card shaft, but the diameter of the card shaft must ensure that there is enough torsion when the wood section is rotated and does not cause damage to the end of the wood section.
In general, the smaller the diameter of the log, the larger the proportion of the wood core, so the diameter of the path spinning wood core is much more important than the diameter of the screw-cut wood core of the large diameter material.
At present, the diameter of the rotary cutter shaft of the trail material can be minimized to 5-6mm.

.

　　7. It is strictly forbidden to inspect and repair all parts in operation.
The debris in the sawing table and the component saw seam shall be removed in time by special tools, and shall not be picked up or rubbed by hand.

　　CNC Veneer peeling machine is the execution of instructions, we give it the instruction is what graphics, CNC veneer peeling machine cut what graphics, we said the directive is the graphics in the programming code, how to generate this code?
There are three main steps:
　　1, analysis of processing requirements and process design, determine the scheme, select the appropriate CNC veneer peeling machine and its wearing parts, determine the reasonable cutting route and cutting dosage.

.

　　2. After starting, should operate empty-load, check and confirm that the saw blade operation direction is correct, the lifting mechanism is flexible, there is no abnormality in operation, no noise, everything is normal, can be operated.

.

Card shaft Units
Single-card shafts, dual-card shafts and veneer peeling machine are well known to plywood industry insiders.
The birth of the veneer peeling machine of the card-free shaft mainly solves the decrease of the diameter of the double card axis veneer peeling machine wood core, and improves the yield of the plate.
However, the veneer peeling machine of the card-free shaft need to carry out 2 spins, the shear loss of the single plate increases, the thickness accuracy of the spinning out of the single plate is not high enough, the rotary cutting speed is not large enough, and so on.
In order to overcome the shortcomings of single-card shafts, dual-card shafts and veneer peeling machine in production, the 3-axis veneer peeling machine was successfully developed in 1996 in the Finnish company after years of development.
The 3-axis veneer peeling machine not only improves the yield, but also improves the spin efficiency and the quality of the veneer.
The machine is equipped with a drive roller to increase the driving force and reduce the torsion of the wood core when spinning the path wood.

　　1. Before use, should check and confirm that the motor, cable are normal, good protection grounding, safe and effective protective device, saw blade selection to meet the requirements, the installation is correct.

.

　　In the correct use of CNC card-free veneer peeling machine for high-quality fast cutting, the cutting process parameters must be deeply understood and mastered, only in this case can make such CNC card-free veneer peeling machine to play its maximum effectiveness, Its cutting workpiece will also achieve the best results.
In the CNC card-free veneer peeling machine cutting workpiece, about the machine plasma power supply cutting current regulation problem is very important, it is the most important cutting process parameters, directly determines the thickness and speed of cutting, that is, cutting capacity.

.

　　5. When the processing parts are delivered to 300mm apart from the saw blade or cut small pieces of material, special tools should be used to feed the material, not directly with the hand to push the material.

.

　　3, according to the program format of CNC system, the generation of parts processing procedures, and then verify and modify it, until the conclusion of qualified processing procedures.
Depending on the complexity of the problem, the number of wrestling processes can be obtained by manual programming or automatic computer programming.

.

　　The main types of veneer peeling machine are the single-card axis veneer peeling machine, the double card axis veneer peeling machine and the non-card axis veneer peeling machine three kinds.
The birth of the veneer peeling machine of the card-free shaft solves the decrease of the diameter of the double-sim veneer peeling machine wood core, and effectively improves the yield of veneer peeling machine.
However, the veneer peeling machine of the card-free shaft should be two times spinning, which directly leads to the increase of the shear loss of the veneer, and the thickness accuracy of the spin-cut veneer is not high, and the rotary cutting speed is not large enough.
In order to overcome the shortcomings of single-card axis, dual-card shaft and veneer peeling machine in production, the three-card axis veneer peeling machine came into being.
The new type of card shaft veneer peeling machine not only effectively solves the problem of the yield, but also effectively improves the spinning efficiency of veneer peeling machine and the production quality of the single board.