Card-free veneer peeling machine manufacturers teach you the knack of doing your job twice more

.


Rotary knife grinding cutting edge grinding and oil knife two steps: When the blade grinding knife, most of the use of cup-shaped grinding wheel, in this grinding to carry out unilateral grinding, at the same time to let the edge outward, so that the grinding out of the blade straightness is good, and the edge will not be easy to break, heat is also relatively small.
Spin knife after grinding wheel edge, the blade will be left with grinding wheel scratches and burrs, then this time need oil stone to repair, referred to as oil knife.
This is to increase the blade sharpness and finish on the swivel knife.
The grinding surface and the back of the rotary knife should be repaired repeatedly using the oil stone.
So that the edge reached the hand touch without backlash, and feel that there is no feeling of cutting hands, using the naked eye to see no white light, so that the edge has reached a sharp.

　A few card veneer peeling machine The choice of cutting current form:
　1, no card veneer peeling machine cutting current increases, plasma arc diameter increases, arc thickening makes the incision wider.

.

　　Veneer peeling machine is also one of the main equipment for the production of veneer, which in a sense is more widely used than planing machines.
Veneer peeling machine According to whether the wood section rotates around its axis can be divided into two categories, concentric rotary and eccentric rotary cutting.
The concentric veneer peeling machine is divided into the veneer peeling machine and the card-free veneer peeling machine of the cam axis.

.

　3, no card veneer peeling machine cutting current is too large to increase the heat load of the nozzle, the nozzle premature damage, cutting quality naturally also decreased, or even can not be normal cutting.
Therefore, the cutting current and the corresponding nozzle should be selected correctly according to the thickness of the material before cutting.

.


　　Using a height meter or equivalent to the height of the center line of the card shaft as a standard, by adjusting the support screws, so that two Rui knife higher than the specified H value in the rotary cutting process, and fasten all nuts.

　　Veneer peeling machine is divided into a card veneer peeling machine cutting machine and a card-free veneer peeling Plywood Making Machine, with advances in technology digital servo control technology is also used in veneer peeling In the production of Machine machine, CNC veneer peeling machine has appeared in recent years.
The appearance of CNC veneer peeling machine not only improves the quality and precision of the production single board, but also greatly improves the production efficiency and the automation degree of the whole machine.

　　The rotary cutter is one of the most important of all veneer peeling machine fittings, and without it in a single device, this device is a waste.
However, the better quality of the rotary cutter if the installation is not in accordance with the standard operation, ignoring the stability of the knife, will affect its overall efficiency and service life in the work.

.


　　In the absence of a post-test angle meter, after changing the knife, with experience to adjust the back angle, driving rotary, to pay attention to the entire rotary cutting process into the knife is smooth.
To observe the bright width of the friction part between the blade of the rotary cutter and the surface of the wood section, it is appropriate to determine whether the posterior angle is adjusted properly.

The rotary knife is an important tool for the veneer peeling machine in the spinning wood section, so the wood section needs to pass through the rotary knife in the spin cutting to obtain the size of the wood section has been out.
Wood section is a relatively high hardness of the object, so veneer peeling machine in the spiral knife if used for more than 3-4 hours, its edge will become blunt, if not replaced in time will lead to the quality of the wood section, so the edge becomes dull, need to be replaced in a timely manner, to the rotary knife grinding.
There are some basic requirements when grinding: A, the angle in the grinding should be correct.
b, after grinding the blade surface finish to be high, sharp tip.
C, coolant should be sufficiently uniform to prevent the blade grind burned.
So how do you grind it? We'll give you an introduction below.

.


5. Flower Roller opening tile, easy to disassemble, more accurate positioning.
Change plate skin thickness, with fine-tuning mechanism, so that the plate skin is easier to adjust uniformity better.

Veneer peeling machine is a good helper for spinning wood, improving the utilization rate of wood, won the welcome of wood machinery Factory.
Now more commonly used veneer peeling machine have card veneer peeling machine, card veneer peeling machine, CNC veneer peeling machine, and so on, they each have its advantages and characteristics.
Today we mainly come to understand the main features of the next dual-boot card-free veneer peeling machine: