Card-free veneer peeling machine computer intelligent end control high leather accuracy-

.

Veneer peeling machine stepless Adjust the speed of the card shaft.
Speed from 0~400r/min or 180r/min, with the diameter of the wood section gradually reduced, automatically improve the speed of the chuck to maintain a constant line speed rotary cut to ensure the quality of the veneer.
The old-fashioned veneer peeling machine speed is manual shift by changing the gearbox gears and the number of teeth to control, the speed can not be stable, can not achieve constant line speed rotary cutting.
When the diameter of the wood core is 110mm, its theoretical maximum rotary speed is 69m/min, and the low speed rotary cut leads to the large crack on the back of the veneer, and the quality of the veneer is poor.

Veneer peeling machine in rotary coniferous and broad-leaved materials, the speed and rotary speed of the veneer peeling machine card shaft are very different.
Coniferous spinning card shaft speed is the fastest 600r/min, wide-leaf rotary cutting card shaft speed of the fastest about 400r/min.
Veneer peeling machine has two gearboxes to meet the needs of different diameter wood rotary cuts.
Two different speeds can be selected by the operator at the operator station through the control key, because the new veneer peeling machine's card shaft speed is stepless speed regulation, so the speed of the card shaft can be automatically selected between 0 and its maximum speed.
In this way, producers can choose any spin speed required for production conditions.

With the increasing scarcity of forest resources, the comprehensive and efficient utilization of wood resource has become an important subject in woodworking equipment manufacturing industry and wood processing industry.
At present, multilayer board manufacturers in the single-board production process, the use of traditional clamping veneer peeling machine processing, this processing method is high precision, good quality.
However, due to the existence of Carcen, the diameter of the rotary cut log in the 200mm or so, it can not be processed on the card veneer peeling machine, and when the diameter of the log is small, the stiffness of the log is reduced, the quality of the rotary cutting veneer is poor, then if the remaining wood core abandoned or processed into a woodworking core board, will result in a great waste of raw materials, thus increasing the production cost of single board.
Therefore, the manufacturers generally use the card-free round wood veneer peeling machine to the remaining wood core to spin again, so that the raw materials have been fully utilized.

When all the normal inspection is complete, it can be put into production and use.
If abnormal conditions occur, immediately contact veneer peeling machine manufacturers after-sales solution or replacement of new machinery and equipment.

Veneer peeling machine Although the degree of automation is high, the installation of automatic pressure bar device, in the spinning process pressure automatically pressurized, no manual pressure bar, but in the veneer peeling machine installation and trial process there are still a lot of considerations need everyone Note that the following veneer peeling machine manufacturers will introduce you to the installation and trial of veneer peeling machine machine tools.

.


Veneer peeling machine's trial.
Pick up each motor power cord and air switch after re-inspection to drive.
The firmness of each motor and the degree of tightness of the chain and belt are checked by means of manual test machine.
Check the operation of each transmission mechanism, and ensure that the link is stable and reliable, normal operation without block.
Check the correctness and firmness of each component position.
Check the correctness and firmness of each protective device.
Check the working conditions of each button and handwheel to ensure sensitive and effective.

.


Veneer peeling machine should be installed on the flat cement ground, the foundation is required to be firm, after the placement of the application of flat ruler to find the level, after the start should ensure that the machine is stable and reliable, do not occur a large tremor, if necessary, can be used cement to add seam or installation ground angle bolts to fasten.

.


When the above inspection is completed, all lubrication is lubricated and the injection oil should be kept clean.
Then gradually one-by-one trial, first try the main motor, check the spindle operation, normal rear shutdown, experimental fast advance and retreat motor, check the tool holder rapid advance and retreat situation, normal rear shutdown, the experimental spindle step up to loosen the motor, check the spindle fast clamping, loosening whether normal, normal rear shutdown, the experimental knife angle adjustment motor, Press the Ascent and drop button to check whether the lifting is normal, there is no block, the normal rear shutdown, the experimental pressure press to loosen the motor, check whether the pressure on the upper and lower movement is normal, there is no block, normal rear shutdown, check whether the motor and reducer operation is normal, installation is solid and reliable, wire rope has no breakage, Shut down normally after the machine.